QuantStudio qPCR

Revolution drives two QuantStudio instruments, and the integration depth is very different between them:

Device	Revolution control
QuantStudio 7 Pro	Full run lifecycle — queue, start, pause, resume, stop, retrieve results, drawer control, power state
QuantStudio 7	Tray in and out, and data file parsing

The specifications below are Thermo Fisher’s for the QuantStudio 6 and 7 Pro systems.

At a glance

Temperature range	4–99.9 °C
Temperature uniformity	0.4 °C
Maximum ramp rate	Up to 9.0 °C/sec (96-well 0.1 mL Fast block)
Block formats	96-well 0.2 mL, 96-well 0.1 mL (Fast), 384-well, TaqMan Array Cards
Dynamic range	10 orders of magnitude
Filter / colour combinations	21 on the QuantStudio 7 Pro (5 on the 6 Pro)
Run time	Less than 30 min

Specifications

Thermal

Temperature range, uniformity and run time are already given in the At a glance table above. Beyond that:

Heating and cooling	Peltier
VeriFlex blocks	3 or 6 independent temperature zones (96-well blocks)
Block size	22.5 × 22.5 × 7 cm

Maximum ramp rate, by block:

Block	Maximum	Average sample
96-well (0.2 mL)	6.5 °C/sec	3.66 °C/sec
96-well (0.1 mL)	9.0 °C/sec	4.81 °C/sec
384-well	6.0 °C/sec	2.92 °C/sec
TaqMan Array Cards	5.0 °C/sec	3.00 °C/sec

VeriFlex is worth knowing about: on 96-well blocks it divides the block into 3 or 6 independent temperature zones, so different cycling conditions can run in the same plate. That is an optimisation tool, and it means “the block temperature” may not be a single value.

Reaction volumes

Block	Volume
96-well 0.1 mL	10–30 µL
96-well 0.2 mL	10–100 µL
384-well	5–20 µL
TaqMan Array Cards	~1.5 µL

Blocks are interchangeable and tool-free to swap, guided by the onboard software — but Thermo Fisher notes the system ships with one block type and others are bought separately, and that blocks are released at intervals so some may not currently be available.

Optics and detection

Filter/colour combinations and dynamic range are already given in the At a glance table above.

Excitation	Bright white LED
Excitation / emission range	450–600 nm / 500–640 nm
Detection	CMOS
Data acquisition	Whole-plate imaging
Multiplexing	5 or 6 targets
Sensitivity	1.5-fold resolution; detect down to 1 copy

Dye compatibility as listed: FAM, SYBR Green I, VIC, JOE, HEX, TET, ABY, NED, TAMRA, Cy3, JUN, ROX, Texas Red, Mustang Purple, Cy5, LIZ and Cy5.5.

System

Dimensions (D × W × H)	52.5 × 33.8 × 54.7 cm
Weight	38 kg
Onboard memory	10 GB, approximately 450 run files
Touchscreen	12 inch capacitive, with real-time application viewing
Communication	Connect Platform, USB, LAN or Wi-Fi
External devices	2D barcode reader via USB
Configuration	Stand-alone, PC connected, or LAN / Wi-Fi to the Connect Platform
Electrical approvals	IEC, CE
Calibration	Engineer calibrated during installation
Data export	RDML, for MIQE compliance

Supported methods — QuantStudio 7 Pro

Running

• Start run / Stop run — begin and abandon a run
• Run template — run from a stored template
• Pause run — pause, holding at a given temperature
• Resume run — resume a paused run

Pause at a temperature is the operation that matters most here. A qPCR run interrupted without a hold temperature is a compromised run; pausing at a defined temperature is what makes an intervention mid-protocol survivable. Thermo Fisher lists programmable and manual pause among the system’s run-programming options.

Run queue

• Send to run queue — add a run to the queue
• List run queue — read what is queued
• Remove from run queue — take a run off the queue

The queue is what lets a schedule stage work without waiting for the block. Runs are under 30 minutes each, so a cell that loads plates faster than the cycler processes them needs somewhere to put them.

Results

• List completed runs — enumerate what is on the instrument
• Download completed run — retrieve a run
• Export results — export result data
• Delete completed run — remove a run by name

With 10 GB of onboard memory holding roughly 450 run files, retrieval and deletion are the pair that keeps an unattended instrument from filling up.

Instrument state

• Open drawer / Close drawer — present the drawer for a robot
• Get plate and block state — read whether a plate is present and which block is fitted
• Power up / Stand by — bring the instrument up, or put it into standby

Get plate and block state is the check to make before committing a transfer: it answers both “is the drawer empty” and “is the right block in there”, and the block determines the reaction volume the plate must match.

Supported methods — QuantStudio 7

• Extend tray / Retract tray — present and withdraw the tray for a robot
• Parse data file — parse a results data file

This is a plate-access and data-parsing integration rather than run control. Runs are started on the instrument.

Integration

The 7 Pro is reached over the network — IP address and port, or a URL — authenticated with an access key, with working and results folders on the host. The older QuantStudio 7 is addressed by instrument name.

Prerequisites

• The instrument must be reachable, and the access key valid, before the device is initialised.
• Working folder and results folder must exist and be writable.
• The block fitted must match the plate the method presents — check with get plate and block state rather than assuming.
• Protocol templates must already exist on the instrument or in Thermo Fisher’s software.

Device configuration

Property	Purpose
IP Address / Instrument Port	Address of the 7 Pro
URL	Service endpoint
Access Key	Credential for the instrument API
Working Folder	Working directory used during a run
Results Folder	Where retrieved results are written
Instrument Name	Identifies the older QuantStudio 7

If you need more of this instrument driven from a schedule, get in touch — the driver is extended on demand.

Operations

These are available from a Run Device Operation step.

Close Drawer

Closes the instrument's plate drawer, under the same interlocks that

Delete Completed Run

Deletes a finished run from the instrument's run history, freeing the

Parameter	Type	Default	Description
Run Name	string	—	Name of the finished run to delete from the instrument, as

Download Completed Run

Copies a finished run's results file off the instrument to the machine

Parameter	Type	Default	Description
Run Name	string	—	Name of the finished run to download, as published by the
Destination Folder	string	—	Folder to write the downloaded results file into, resolved on the

Export Results

Converts a downloaded results file into report files, written as CSV

Parameter	Type	Default	Description
EDS File Path	string	—	Full path to the downloaded results file to export, resolved on
Destination Folder	string	—	Folder to write the exported files into, resolved on the machine
File Name Prefix	string	—	Prefix for the names of the exported files. The results file's own
Format	string	—	Export file format: CSV, XLS, XLSX, TXT, ZIP or RDML, matched
As Single File	bool	—	Whether to write one combined file instead of a separate file for

Get Instrument Info

Reports the instrument's identity, serial numbers, firmware and

Get Plate And Block State

Reports whether a sample block is fitted to the instrument and whether

Get Run Progress

Reports the active run's name and how far it has reached through the

Get Status

Reports what the instrument is doing now: its state, drawer position,

List Completed Runs

Reports how many finished runs the instrument still holds in its run

List Run Queue

Reports how many templates are waiting in the instrument's run queue,

Open Drawer

Opens the instrument's plate drawer, so that a plate can be placed on

Pause Run

Pauses the run in progress, holding the sample block at the temperature

Parameter	Type	Default	Description
Temperature Celsius	double	—	Temperature in degrees Celsius at which the sample block is held

Power Up

Brings the instrument out of standby and back to an idle, run-ready

Raise Error

Makes this device report a failure on demand: the step fails with an error naming the device, and the operator is offered the usual error recovery choices. No command reaches the instrument and nothing moves, and the failure is raised in simulation as well as on a real system, so this is the step to use when rehearsing how a schedule handles a device failure.

Remove From Run Queue

Withdraws a waiting template from the instrument's run queue,

Parameter	Type	Default	Description
Template File Name	string	—	Name of the queued template to withdraw, as it appears in the run

Resume Run

Continues a run that was paused, taking the protocol up from the point

Run Template

Starts a qPCR run from an EDT template file, waits for the instrument

Parameter	Type	Default	Description
Template File Path	string	—	Full path to the EDT run template that defines the protocol and
Run Name	string	—	Name that identifies this run on the instrument and names the
Plate Barcode	string	—	Barcode to record in the run's plate setup. When one is supplied
Timeout Seconds	int	—	How long to wait for the whole run, in seconds, counting the lamp
Download Results	bool	—	Whether to download the results file once the run finishes. The

Send To Run Queue

Uploads an EDT template file to the instrument's own run queue without

Parameter	Type	Default	Description
Template File Path	string	—	Full path to the EDT run template to upload to the instrument's

Stand By

Puts the instrument into its low-power standby state, which turns the

Start Run

Starts a qPCR run from an EDT template file and returns as soon as the

Parameter	Type	Default	Description
Template File Path	string	—	Full path to the EDT run template that defines the protocol and
Run Name	string	—	Name that identifies this run on the instrument and names the
Plate Barcode	string	—	Barcode to record in the run's plate setup. When one is supplied

Stop Run

Aborts the run in progress. The run ends where it stands and cannot be